Initial Setup Steps for Identity Provisioning with Crowdin

GMOトラスト・ログインチーム
  • Updated

This page describes the initial setup steps for using TrustLogin as the source of identity
to perform Identity Provisioning to Crowdin.

Note: For detailed instructions on operating Crowdin, please refer to the documentation provided by Crowdin.

Item Details
Pre-check
  • Crowdin administrator privileges are required.
Setup Flow / Manual

Note: After connecting TrustLogin and Crowdin using the steps on this page,
　please proceed to configuring user synchronization.
Provisioning Target 〇 Supports user provisioning
〇 Supports group provisioning
SAML Authentication Setup Manual －
Notes
  • None in particular

Setup Steps

Crowdin Settings

  1. Log in to Crowdin with administrator privileges, and click "Store".


  2. Search for "SCIM".

  3. Click "SCIM User Provisioning" that appears in the search results.

  4. Click "Install".
    Note: If it is already installed, skip this step.

  5. Click "SCIM User Provisioning".

    Crowdin_ID_07.png

  6. Copy the "SCIM 2.0 Endpoint" and "OAuth Bearer Token" to your clipboard.

    Note: The token cannot be viewed again after you "Save". Please make sure you have copied it before proceeding.

    [Crowdin]_ID_17.png



    This completes the preparation on the Crowdin side. Next, configure the settings on the TrustLogin side.

TrustLogin Settings

  1. Log in to the TrustLogin Admin Page, and from the "Admin Page > Settings > Optional Features" menu,
    open "Settings" next to "Identity Provisioning".
    IDProvServiceCommon01.png

  2. Click "Add Service".
    IDProvServiceCommon02.png
  3. On the Add Service screen, search for and select "Crowdin", then click the "Add" button.
    [Crowdin]_ID_18.png
  4. You will be redirected to the "Identity Provisioning > Crowdin" page.
    Click the "Edit" button.
    [Crowdin]_ID_19.png

  5. Open "Access Settings", enter the following values for the settings items, and click "Save".

    SCIM URL The value of "SCIM 2.0 Endpoint" you copied in step 6 of Crowdin Settings
    Access Token The value of "OAuth Bearer Token" you copied in step 6 of Crowdin Settings

    Crowdin_ID_15.png

  6. Click the "Connect" button in the upper right of the screen.
    NotConnected_IDProv.png

  7. Once the button status updates to "Connected", the initial setup is complete.
    Connected_IDProv.png

Next step: The manual for configuring user synchronization is available here

Values You Can Configure in Attribute Mapping

You can map any attribute on the TrustLogin side to any attribute on the Crowdin side.
For configuration instructions, see here

Available Default Functions

Was this article helpful?
  1. ホーム
  2. Identity Provisioning - Service Settings
  3. Initial Setup Steps for Identity Provisioning with Crowdin

Initial Setup Steps for Identity Provisioning with Crowdin

GMOトラスト・ログインチーム
  • Updated

This page describes the initial setup steps for using TrustLogin as the source of identity
to perform Identity Provisioning to Crowdin.

Note: For detailed instructions on operating Crowdin, please refer to the documentation provided by Crowdin.

Item Details
Pre-check
  • Crowdin administrator privileges are required.
Setup Flow / Manual

Note: After connecting TrustLogin and Crowdin using the steps on this page,
　please proceed to configuring user synchronization.
Provisioning Target 〇 Supports user provisioning
〇 Supports group provisioning
SAML Authentication Setup Manual －
Notes
  • None in particular

Setup Steps

Crowdin Settings

  1. Log in to Crowdin with administrator privileges, and click "Store".


  2. Search for "SCIM".

  3. Click "SCIM User Provisioning" that appears in the search results.

  4. Click "Install".
    Note: If it is already installed, skip this step.

  5. Click "SCIM User Provisioning".

    Crowdin_ID_07.png

  6. Copy the "SCIM 2.0 Endpoint" and "OAuth Bearer Token" to your clipboard.

    Note: The token cannot be viewed again after you "Save". Please make sure you have copied it before proceeding.

    [Crowdin]_ID_17.png



    This completes the preparation on the Crowdin side. Next, configure the settings on the TrustLogin side.

TrustLogin Settings

  1. Log in to the TrustLogin Admin Page, and from the "Admin Page > Settings > Optional Features" menu,
    open "Settings" next to "Identity Provisioning".
    IDProvServiceCommon01.png

  2. Click "Add Service".
    IDProvServiceCommon02.png
  3. On the Add Service screen, search for and select "Crowdin", then click the "Add" button.
    [Crowdin]_ID_18.png
  4. You will be redirected to the "Identity Provisioning > Crowdin" page.
    Click the "Edit" button.
    [Crowdin]_ID_19.png

  5. Open "Access Settings", enter the following values for the settings items, and click "Save".

    SCIM URL The value of "SCIM 2.0 Endpoint" you copied in step 6 of Crowdin Settings
    Access Token The value of "OAuth Bearer Token" you copied in step 6 of Crowdin Settings

    Crowdin_ID_15.png

  6. Click the "Connect" button in the upper right of the screen.
    NotConnected_IDProv.png

  7. Once the button status updates to "Connected", the initial setup is complete.
    Connected_IDProv.png

Next step: The manual for configuring user synchronization is available here

Values You Can Configure in Attribute Mapping

You can map any attribute on the TrustLogin side to any attribute on the Crowdin side.
For configuration instructions, see here

Available Default Functions